OPTO
◆OPIC∗
Output
<Compact, SMT type> (1-1)
:
Approved,
o:
Under application
PHOTOCOUPLERS
∗
“OPIC” (Optical IC) is a trademark of SHARP Corporation. An OPIC consists of a light-
detecting element and a signal-processing circuit integrated onto a single chip.
(Ta = 25°C)
Model No.
Internal
connection
diagram
Approved by
safety
standards*
2
Features
Absolute maximum
Electro-optical characteristics*
1
ratings
Low level output voltage
Threshold input current
Isolation
Package
Forward voltage
current
I
FLH
V
OL
I
FHL
(AC)
I
F
RL
Ta
I
OL
I
F
(mA) (mA)
UL VDE*
3
(V)
Viso (rms)
(mA) (mA)
(Ω)
(°C)
(mA)
MAX. MAX.
MAX.
(kV)
–
–
Mini-flat
5-pin
50
50
3.75
3.75
0.4
0.4
0 to +70
0 to +70
16
16
4
0
2.0
–
–
2.0
280
280
PC400J00000F
PC401J00000F
A
Digital output,
normal-off operation
Digital output,
normal-on operation
Built-in preamplifier,
high speed transmission
(2 Mb/s),
For flow soldering
High speed (10 Mb/s),
High CMR (10 kV/µs),
For flow soldering
High speed (10 Mb/s),
High CMR (10 kV/µs),
For flow soldering,
Solder heat resistance:
270°C
High speed (25 Mb/s),
High CMR (10 kV/µs),
For flow soldering,
Solder heat resistance:
270°C
High speed (15 Mb/s),
High CMR (10 kV/µs),
For flow soldering
High speed (15 Mb/s),
High CMR (10 kV/µs),
For flow soldering,
Solder heat resistance:
270°C
High speed (10 Mb/s),
For flow soldering,
Solder heat resistance:
270°C
2ch output
A
PC456L0NIP0F
A
25
3.75
0.6
–40 to +85
4.4
10
5.0
–
20 k
PC410L0NIP0F
20
3.75
0.6
–40 to +85
13
5
5.0
–
350
PC410S0NIP0F
20
SOP
8-pin
–
–*
4
3.75
0.6
–40 to +85
13
5
5.0
–
350
PC412S0NIP0F
3.75
1
–40 to +85
4
V
IN
=
V
IL
–
–
–
PC411L0NIP0F
Mini-flat
5-pin
20
3.75
0.1
–40 to +85 0.02
12
6.0
–
–
PC411S0NIP0F
20
SOP
8-pin
–
20
3.75
0.1
–40 to +85 0.02
12
6.0
–
–
PC4D10SNIP0F
3.75
0.6
–40 to +85
13
5
5.0
–
–
A: Rated voltage circuit
*1 Each item is measured at Vcc=5V. (PC400, PC401)
*2 Please refer to Specification Sheets for model numbers approved by safety standards.
*3 Optionally available.
*4 No forward current rating for voltage input (rated input voltage: –0.5 to 6.0 V).
72
Notice
In the absence of confirmation by device specification sheets, SHARP takes no responsibility for any defects that may occur in
equipment using any SHARP devices shown in catalogs, data books, etc.
Except where specially indicated, models listed on this page comply with the RoHS Directive*. For details, please contact SHARP.
*RoHS Directive: Prohibits use of lead, cadmium, hexavalent chromium, mercury and specific brominated flame retardants
(PBBs and PBDEs), with certain exceptions.
Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device.