ANALOG AND MIXED SIGNAL PRODUCTS (continued)
Power Actuation — Powertrain Control and Engine Management
Product
MC33800
Description
Engine Control Integrated Circuit capable of driving a
combination of six MOSFETs and ten Low Side loads.
Engine Control Integrated Circuit capable of driving a
combination of four MOSFETs or IGBT gates and four
Low Side loads.
5 Input Solenoid Monitor IC
Programmable H-Bridge Power IC
Main Characteristics
Engine control IC, with six MOSFET gate pre-drivers, eight
Low Side Switches, and two constant current low side
switches
Engine control IC with four MOSFET/IGBT gate drivers and
four low side switches.
5 input solenoid monitoring to verify proper electrical and
mechanical solenoid operation.
Designed to drive a DC motor in both forward and reverse
shaft rotation under pulse-width modulation (PWM) of
speed and torque.
H-Bridge power IC for DC servo motor control like engine
throttle control. Load can be PWM’ed up to 20 KHz
This IC contains three high-side FET pre-drivers and three
low-side FET pre-drivers, with parallel and SPI control.
22 inputs contact monitoring (14 GND, 8 configurable), 4.0
mA or 32 mA pulse wetting current, low-power mode
interrupt capability, wakeup.
Peak Current
Limit (A)
2 @ 6.0
6 @ 2.0
1 @ 2.5
6.0
R
DSON
(mOhm)
8 @ 700
1 @ 250
100
Input
Control
1
SPI,
Parallel
SPI,
Parallel
SPI
SPI,
Parallel
Parallel
SPI,
Parallel
SPI
Regulation
Voltage
—
Operating
Voltage (V)
5 to 36
Packaging
54-pin SOICW
Status
Production
EVB
Production
1Q/2008
Production
1Q2008
Production
1Q2008
Production
2Q2008
Production
Nov. 2007
EVB
Production
MC33810
—
4.5 to 36
32-pin SOICW
Exposed Pad
16-pin SOICW
30-pin HSOP
MC33811
MC33899
—
15.0
—
90
—
—
10.5 to 15.5
6 to 26.5
MC33926
MC33927
5.0A Throttle Control H-Bridge
Three-Phase Field Effect Transistor Pre-Driver for three-
phase motor control
22 input Multiple Switch Detect Interface with 32 mA
Wetting Current and Wake-up
8.0
—
120
—
—
—
8 to 28
8 to 40
32-pin PQFN
54-pin SOICW
Exposed Pad
32-pin SOICW
Exposed Pad
MC33975
MC33975A
1
—
—
—
5.5 to 26.5
Products available with SPI Control work with the KITUSBSPIEVME and the KITUSBSPIDGLEVME USB-SPI Interface Boards.
Network Transceivers — CAN Physical Interface Components
Product
Description
Main Characteristics
Communication
Protocol
Operating
Voltage
(V)
5.5 to 27
Current
Limitation Standby
(µA)
Typ
Max
60
150
Other Features
Control and
Status
Reporting
1
4 MHz SPI
(for diag)
Protection
Features
Packaging
Status
MC33742
MC33742S
System Basis Chip with Enhanced
High Speed CAN (250k to 1Mbps)
SBC, Dual V
REG
, Enhance HS CAN with CAN HS dual wire
Bus failure diagnostic capability, 4 wakeup
inputs, pin and function compatible with
MC33989
Dual V
REG
, LS CAN, 2 wakeup inputs
Low or high (33.3 kbps or 83.3 kbps data
rates, wakeup capability (GMW3089 v2.3
compatible)
CAN low-speed,
dual wires
SW CAN
Low power modes, remote and
local wakeup capabilities
Current and
thermal protection
for CAN and
regulator
Fault tolerant
28-pin SOICW
48-pin QFN
Production
EVB
MC33889B
MC33889D
MC33897C
MC33897D
System Basis Chip Lite with Low-
Speed CAN
Single-Wire CAN
5.5 to 27
100
100
Dual voltage regulator,
watchdog, wake input, sleep
and stop modes
Regulator Control Output
Waveshaping Undervoltage
lockout detect and handle loss
of GND
Dual voltage regulator,
watchdog, wake input, sleep
mode, and cyclic sense
SPI 4 MHz
28-pin SOICW
Production
6.0 to 27
45
60
2 Mode
Control Pins
Thermal shutdown,
current limit
14-pin SOICN
8-pin SOICN
Production
MC33989
1
System Basis Chip with High-Speed SBC dual V
REG
, HS CAN, 4 wakeup
CAN
inputs
CAN high-speed,
dual wires
5.5 to 27
150
150
SPI 4 MHz
n/a
20-pin HSOP
28-pin SOICW
Production
EVB
Products available with SPI Control work with the KITUSBSPIEVME and the KITUSBSPIDGLEVME USB-SPI Interface Boards.
A change bar appears in the left margin to mark the location of new or revised information.
SG187–5
Rev 29