ANALOG AND MIXED SIGNAL PRODUCTS (continued)
Power Actuation — Powertrain Control and Engine Management
Product
MC33800
Description
Engine Control Integrated Circuit capable of driving a
combination of six MOSFETs and ten Low Side loads.
Engine Control Integrated Circuit capable of driving a
combination of four MOSFETs or IGBT gates and four
Low Side loads.
5 Input Solenoid Monitor IC
Programmable H-Bridge Power IC
Main Characteristics
Engine control IC, with six MOSFET gate pre-drivers, eight
Low Side Switches, and two constant current low side
switches
Engine control IC with four MOSFET/IGBT gate drivers and
four low side switches.
5 input solenoid monitoring to verify proper electrical and
mechanical solenoid operation.
Designed to drive a DC motor in both forward and reverse
shaft rotation under pulse-width modulation (PWM) of
speed and torque.
H-Bridge power IC for DC servo motor control like engine
throttle control. Load can be PWM’ed up to 20 KHz
This IC contains three high-side FET pre-drivers and three
low-side FET pre-drivers, with parallel and SPI control.
22 inputs contact monitoring (14 GND, 8 configurable), 4.0
mA or 32 mA pulse wetting current, low-power mode
interrupt capability, wakeup.
Peak Current
Limit (A)
2 @ 6.0
6 @ 2.0
1 @ 2.5
6.0
R
DSON
(mOhm)
8 @ 700
1 @ 250
100
Input
Control
1
SPI,
Parallel
SPI,
Parallel
SPI
SPI,
Parallel
Parallel
SPI,
Parallel
SPI
Regulation
Voltage
-
Operating
Voltage (V)
5 to 36
Packaging
54-pin SOICW
Status
Production
EVB
Production
1Q2008
Production
1Q2008
Production
1Q2008
Production
2Q2008
Production
Nov. 2007
EVB
Production
MC33810
-
4.5 to 36
32-pin SOICW
Exposed Pad
16-pin SOICW
30-pin HSOP
MC33811
MC33899
-
15.0
-
90
-
-
10.5 to 15.5
6 to 26.5
MC33926
MC33927
5.0A Throttle Control H-Bridge
Three-Phase Field Effect Transistor Pre-Driver for three-
phase motor control
22 input Multiple Switch Detect Interface with 32 mA
Wetting Current and Wake-up
8.0
-
120
-
-
-
8 to 28
8 to 40
32-pin PQFN
54-pin SOICW
Exposed Pad
32-pin SOICW
Exposed Pad
MC33975
MC33975A
-
-
-
5.5 to 26.5
1. Products available with SPI Control work with the KITUSBSPIEVME and the KITUSBSPIDGLEVME USB-SPI Interface Boards.
Network Transceivers — CAN Physical Interface Components
Product
Description
Main Characteristics
Communication
Protocol
Operating
Voltage
(V)
5.5 to 27
Current
Limitation Standby
(µA)
Typ
Max
60
150
Other Features
Control and
Status
Reporting
1
4 MHz SPI
(for diag)
Protection
Features
Packaging
Status
MC33742
MC33742S
System Basis Chip with Enhanced
High Speed CAN (250k to 1Mbps)
SBC, Dual V
REG
, Enhance HS CAN with CAN HS dual wire
Bus failure diagnostic capability, 4 wakeup
inputs, pin and function compatible with
MC33989
Dual V
REG
, LS CAN, 2 wakeup inputs
Low or high (33.3 kbps or 83.3 kbps data
rates, wakeup capability (GMW3089 v2.3
compatible)
CAN low-speed,
dual wires
SW CAN
Low power modes, remote and
local wakeup capabilities
Current and thermal
protection for CAN
and regulator
Fault tolerant
28-pin
SOICW
48-pin QFN
28-pin
SOICW
Production
EVB
MC33889B
MC33889D
MC33897C
MC33897D
System Basis Chip Lite with Low-
Speed CAN
Single-Wire CAN
5.5 to 27
100
100
Dual voltage regulator,
watchdog, wake input, sleep
and stop modes
SPI 4 MHz
Production
6.0 to 27
45
60
Regulator Control Output
2 Mode Control
Waveshaping Undervoltage
Pins
lockout detect and handle loss
of GND
Dual voltage regulator,
watchdog, wake input, sleep
mode, and cyclic sense
SPI 4 MHz
Thermal shutdown, 14-pin SOICN Production
current limit
8-pin SOICN
MC33989
System Basis Chip with High-Speed SBC dual V
REG
, HS CAN, 4 wakeup
CAN
inputs
CAN high-speed,
dual wires
5.5 to 27
150
150
n/a
20-pin HSOP
28-pin
SOICW
Production
EVB
1. Products available with SPI Control work with the KITUSBSPIEVME and the KITUSBSPIDGLEVME USB-SPI Interface Boards.
A change bar appears in the left margin to mark the location of new or revised information.
SG1002–6
SG1002Q42007
Home Index Pages Text
Previous Next
Pages: Home Index